1WARNINGA radio-controlled model is not a toy and is not intended for persons under 16 years old. Keepthis kit out of the reach of younger children,
103. Remove the pins in each hinge and, keepingthe elevator/stab assembly in position, apply 3or 4 drops of thin CA to each hinge, on boththe top an
113. Turn the fuselage over and pull the pushrodout to the elevator. Place the control horn so that it is at the endof the pushrod and the clevis h
123. Measure the length of the pushrod to theservo arm hole and make a 90 degree bend. Mount the swivel keeper on to the wire andclip in place.4.
133. Place your motor on the motor mounts, Center the motor between the mounts. Measure from the firewall to the prop drivewasher 4-7/8 “. Mark
146. Install the throttle servo into the servo tray. Insert the pushrod wire through the connectoron the servo arm. mount the servo arm onto the s
156. Attach the two pieces of 5mm tubing to thetwo tank outlets. They are different colors soyou can tell which is the vent and which is thefuel pic
163. Mount the fairing on the bottom of the planeas shown above. Drill a 1/16” hole for the brass straps andscrew them down with the #2 x 3/8 screw
173. Keep the hole in the front of the cowl centeredon the engine.4. Screw the cowl to the fuselage using #2 x 5/16screws.WINDOWS1. Collect the
18Cut alongthis line5. Temporary tape the front Windshield in placeon the fuselage. Mark the side of the Windshield using a pen orpencil where show
195. Attach the wing to the strut by screwing theclevises in & out to the straps.Caution:Tighten the wing struts just enoughso that you do not h
2ITEMS NEEDED TO COMPLETE THIS AIRCRAFT 1 RADIO GUIDANCE SYSTEM (4 CHANNELMINIMUM REQUIRED WITH 5 SERVOS) 2 12” AILERON SERVO EXTENSION WIRES 1 Y-
202. Take the 8 flat brackets and bend in themiddle to about a 30 degree angle. Use the three 2-56 x 1/2” screws with a wash-er under the head, and
21The wires should just be snug with no slop,don’t distort the flying surfaces withtoo much tension.8. Pass the cable through the brass tube,through
22ThrowsUse these control throws for the firstflights. Work your way up to more throwmovement when you are comfortablewith the Cub ARF.Elevator 3/4” U
23
24
3INTRODUCTIONUSING THIS INSTRUCTION MANUALBefore you begin assembling your Cub ARF, take sometime to read through this entire instruction book. It is
41. Collect the following parts:(1) Left wing(1) Right wing(1) Left aileron(1) Right aileron(8) Jet hinge2. Locate the pre-cut aileron hinge slots
5AILERON SERVO INSTALLATION1. Collect the following parts:(1) Left wing(1) Right wing(2) Servos(2) 12” Servo Extensions(1) Wheel Collar(1) 24” Threa
6AILERON CONTROL HORN INSTALLATION1. Collect the following items(2) Large control horn with back plate(4) 2-56 x 3/4" screw(2) .072 x 10"
7WING STRUT BRACKET INSTALLATION1. COLLECT THE FOLLOWING ITEMS:(4) STRUT MOUNTING BRACKET(4) #2 X 3/8 SHEET METAL SCREW2. Place a small drop of th
85. From the center point on the stab, draw a ver-tical line up to the top of the stab. Place masking tape on the top of the fuse, justin front of
92. Slide the fin mounting post into the rear of thefuselage. Check the fit. The fin should fit easily into theslot at the rear of the fuselage a
Commentaires sur ces manuels